Cheap Car Wireless Bluetooth AUX Adapter HIFI Stereo Audio Music
Main Features: 1. Plug & Play: installed via original CD changer port, easy and fast, perfectly integrated with the car. 2. Wireless A2DP Playback: easily streaming music of Bluetooth devices into a factory car stereo system. 3. Hi-fi Sound Quality: Connected to car stereo via wire harness, no interference and no loss of sound quality, rivaling original CD sound. 4. Allow you to easily have a popular configuration of advanced car stereo, is the best choice for safe driving and enjoying digital music. Specification: Voltage Input : 4.5V ~14.6V DC Operational Current : 600mA Standby Current: 20mA Operating Temperature: -35℃~+75℃ DAC Resolution : 20bit Total Harmonic Distortion: 0.05% SN Ratio : 90dB Frequency Response: 20HZ-20KHZ Package includes: 1x Universal Car Bluetooth 5.0 AUX Audio Cable Note: 1. Doesn't support hands-free phone call(HFP): It doesn't supports answer/hang up etc. Via car radio buttons and steering wheel buttons. 2. Doesn't support Bluetooth AVRCP Control: Prev/Next Track, Pause/Play, Fast forward/backward via car radio buttons or steering wheel buttons. Installation Guide: Installation Preparation： 1. This product operates on a vehicle with 12 volts or 5-volt DC negative ground system. Do not use it on another voltage system. 2. This product only fits OEM or aftermarket car stereo with CD changer port and different solutions of Bluetooth adapter would be adopted according to different brands of vehicles or different car radios. 3. Make sure the car stereo is powered off before installation. Otherwise, the car stereo may be damaged. It is suggested to install it in a car dealer shop or professional car stereo store. 4. Usually, the car stereo needs to be removed so as to plug the Bluetooth kit main connector into the CD changer port on the radio pack. For some car models, Bluetooth kits can be installed in the glove box or trunk where the external CD changer port is located. 5. Please read the car stereo wiring diagram carefully before installation (normally on the top side of the car stereo）. Check and confirm where are the following ports on the back of the stereo: CD changer port, B+/Ub+/12V ACC port(different car stereos have different names. such as BAT, Bup+, B-U, MEM +12, KL.30), and GND port. Installation Steps： 1. Turn off the car engine and remove the key from the ignition, if the car radio uses a security code, make sure that you have the code before unplugging the radio. 2. Unmount the radio from the dash in order to get access to the back side of the radio, and find the CD Changer port at the back of the radio. For details on unmounting, please refer to the car user manual or car stereo manual, or ask professional staff to unmount the radio. 3. Connect the wire harness to the car stereo radio module unit in advance. Be sure to make a firm connection. Then attach the wire harness connector to the back of the stereo to the CD changer port. 4. For some car models, connect the red wire to the B+/Ub+/12V ACC port (different car stereos have different names. such as BAT, Bup+, B-U, MEM +12, KL.30) or other correct ACC power or 5 / 12V battery power. Connect the black wire to the GND port of the head unit power module unit. 5. Turn on the car and power on the car Head Unit, press the CD (or Disc / Mode / CDC / SOURCE / AUX) button once or twice to switch to music play mode. 6. Turn on the Bluetooth function of the mobile phone, search and pair with a Bluetooth device named ''BT5909'', Mobile phone will be able to connect to BTA after being paired successfully. Test with a mobile phone to confirm whether Bluetooth music work normally. 7. After a successful test, re-assemble the radio, and put the wire harness and module unit box in the proper place (glove box, storage box, etc.), fasten the screws between the module unit and wire harness. Put the back car head unit into its original position. Now the installation is finished. Important Installation Notes： 1. As to some vehicles with an external CD Changer, which occupies the original CD changer port, a Parallel Harness is needed to keep the use of the original CD changer (For some models only). 2. As for Clarion protocol radios, such as some Subaru radios and Suzuki radios, it requires totally unplugging the wire harness from car power before installation. Moreover, it is easy to plug the connector in the opposite direction on Clarion radios, which causes short circuits. Make sure the connector is plugged in the correct direction. 3. As for installation on CAN-Bus radios of Peugeot/Citroen, Renault, Ford (new) and Mazda (new), and Opel, it is required to unplug the radio from the power before installation. Otherwise, the Bluetooth kit might not work properly or the radio might be damaged. Regarding Peugeot/Citroen without a pre-installed CD Changer, to enable the Bluetooth kit to work, the CD Changer function must be activated by professional tools. Please enquire the Peugeot/Citroen dealer on how to activate the CD Changer function. 5. As per BMW radios with CD Changer, the CD Changer must be completely disconnected before installation (The 3-pin and the 6-pin connector, which are located in the trunk, must be disconnected), otherwise, the Bluetooth kit will not be recognized. Besides, if the BMW radios are with DSP, an extra DSP kit and a specific Bluetooth kit would be used. 3 Applicable Car Models Toyota Honda Volkswagen Benz Suzuki Nissan Porsche Ford Fiat Acura BMW Wolvo Mazda Skoda Peugeot Renault Citroen Opel, etc This product only needs to have an AUX interface or the original The car CD player can be used with the AUX interface. (Please consult or confirm that you have an AUX interface before purchasing) 1. Not compatible with stereos that have 6 CD Player built into the stereo 2. Not compatible with the ''blue & me '' Bluetooth audio streaming feature Also many devices from 2007 in connection with the Bluetooth model KCE-400BT.
🚗[Bluetooth 5.3 Clearer Sound & Enhanced Microphone] JOYROOM Bluetooth car adapter is Equipped with the latest Bluetooth 5.3 technology, optimizing
Bluetooth 5.3 AUX Adapter [Multifunction Button& Battery Life Display] Noise Cancelling Music Receiver for Car/Home Stereo/Wired Headphones/Hands-Free
BT200 NFC Bluetooth Receiver 3.5mm AUX RCA Jack A2DP Hifi Wireless
Review: JOYROOM Bluetooth 5.3 Car Adapter with Dual Mics and Noise
【ADVANCED BLUETOOTH 5.0 RECEIVER】: A solution for cars with non Bluetooth capabilities, enjoy handsfree calling, GPS and streaming music while in
Bluetooth Aux Adapter for Car, SONRU Bluetooth 5.0 Receiver for Car,Wireless Audio Adapter Portable Hands-Free Car Kits with RCA AUX 3.5mm for
USA HIFI Car Bluetooth Music Receiver A2DP 3.5mm AUX Audio Jack
Logitech Bluetooth Music Receiver review: Forget the aux cord
Stay Connected Bluetooth 5.0 provides an ultra-stable connection up to 10 m away from your device. The Bluetooth adapter can turn a non-Bluetooth device into a Bluetooth-enabled device as a receiver, and receive superior quality and stereo sound This Bluetooth Transmitter can receive and send functions integrated into one of the Bluetooth devices, long standby time, product appearance, easy to operate, free to receive and transmit audio signals.
UGREEN Bluetooth 5.0 Aux Car Adapter
Tika Bluetooth Receiver, Aigital Wireless 3.5mm Aux Audio Reception Adapter Car Kit Handsfree Home Stereo Music Speaker System Pair with iPhone 7 8 x
Car Wireless Bluetooth Receiver Module AUX Adapter HIFI Sound
